j 'essaye de connecter ma passerelle openbsd 3.5 avec un modem sagem 908 en ethernet
ma carte reseau est "rl1"!!!
mon fichier ppp.conf est celui-ci :
default:
set log Phase Chat LCP IPCP CCP tun command
set redial 15 28800
set reconnect 15 28800
ppoe:
set device "!usr/sbin/ppoe -i rl1"
disable acfcomp protocomp
set timeout 30
set speed sync
enable lqr
set mtu max 1492
set mru max 1492
set dial
set login
disable ipv6cp
set authname xxxxxxxx@freeadsl
set authkey xxxxxxx
add! default HISADDR
enable mssfixup
enable dns
mais kan g lance ppp -ddial pppoe celui ci reste bloque et refuse de se connecter
le contenu de mes log est celui-ci :
Oct 5 17:54:44 serveur ppp[26836]: tun0: Phase: deflink: 10 packets in, 0 packets out
Oct 5 17:54:44 serveur ppp[26836]: tun0: Phase: total 57 bytes/sec, peak 0 bytes/sec on Tue Oct 5 17:
54:44 2004
Oct 5 17:54:44 serveur ppp[26836]: tun0: Phase: deflink: HUPing 5459
Oct 5 17:54:44 serveur ppp[26836]: tun0: Phase: deflink: hangup -> opening
Oct 5 17:54:44 serveur ppp[26836]: tun0: Phase: deflink: Enter pause (15) for redialing.
Oct 5 17:54:44 serveur ppp[26836]: tun0: Chat: deflink: Reconnect try 10 of 28800
Oct 5 17:54:59 serveur ppp[26836]: tun0: Chat: deflink: Redial timer expired.
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: Connected!
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: opening -> dial
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: dial -> carrier
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: carrier -> login
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: login -> lcp
Oct 5 17:54:59 serveur ppp[26836]: tun0: LCP: FSM: Using "deflink" as a transport
Oct 5 17:54:59 serveur ppp[26836]: tun0: LCP: deflink: State change Initial --> Closed
Oct 5 17:54:59 serveur ppp[26836]: tun0: LCP: deflink: State change Closed --> Stopped
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: read (0): Connection reset by peer
Oct 5 17:54:59 serveur ppp[26836]: tun0: LCP: deflink: State change Stopped --> Closed
Oct 5 17:54:59 serveur ppp[26836]: tun0: LCP: deflink: State change Closed --> Initial
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: Disconnected!
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: lcp -> logout
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: logout -> hangup
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: Disconnected!
Oct 5 17:54:59 serveur ppp[26836]: tun0: Phase: deflink: Connect time: 0 secs: 57 octets in, 0 octets o
ut
perso je gallere carrement donc si quelqu'un avait une idee!! je prends!!!
tchao jerem