IPCOP 1.4.0a1 et B-FOCUS Modem ADSL ETH ATM ECI L

Forum traitant de la distribution sécurisée montante nommée IP cop et basée sur la distribution Smoothwall. C'est à l'heure actuelle le forum le plus actif du site.

Modérateur: modos Ixus

IPCOP 1.4.0a1 et B-FOCUS Modem ADSL ETH ATM ECI L

Messagepar Psycotrope » 17 Sep 2004 08:49

Bonjour a tous, je viens d'installer IPCOP 1.4.0a1 et je n'arrive pas a faire fonctionner mon modem.

Config :

2 carte Realtech 8139 une red, une verte
B-FOCUS Modem ADSL ETH ATM ECI L
install en PPPoE (setup)
Param WEB PPPoE


Quelqu'un a le meme ? comment fo faire ! :?

Chose bizzarre, j'ai pris les cable d'origine, entre l'ordi et le PC le cable est droit !!! avecun croisé sa ne marche pas non plus !!!!


Mes Log PPP :

08:01:44 pppd Using interface ppp0
08:01:44 pppd Connect: ppp0 <--> /dev/pts/0
08:01:44 pppoe PPP session is 7811
08:01:44 pppd LCP terminated by peer
08:01:44 pppoe Session 7811 terminated -- received PADT from peer
08:01:44 pppoe Sent PADT
08:01:44 pppd Modem hangup
08:01:44 pppd Connection terminated.
08:01:44 pppd Exit.



Help Me !!
Psycotrope
Quartier Maître
Quartier Maître
 
Messages: 21
Inscrit le: 17 Sep 2004 08:26

Messagepar Franck78 » 17 Sep 2004 09:42

Hello,


Le help est simplissime: installes la DERNIERE version qui est la RC4.

1 million de problèmes de modem corrigé depuis cette viellerie. D'ailleur comment es-tu tombé sur cette daube ?

Prends ici:
viewtopic.php?t=20714&start=0



Salut
Franck
L'art de poser une question sur ce site afin d'obtenir la réponse
A LIRE
Avatar de l’utilisateur
Franck78
Amiral
Amiral
 
Messages: 5625
Inscrit le: 20 Fév 2004 01:00
Localisation: Paris

Messagepar guiguid » 17 Sep 2004 10:55

il l'a trouvé dans la section telechargement !


a1 a2 a3 a4 a5 a6 a7 a8 a9 a10 a11 a12 b1 b2 b3 b4 b5 b6 b7 b8 b9 rc1 rc2 rc3 rc4

ca te fais pas moins de 24 versions de retard !!!!!!
Avatar de l’utilisateur
guiguid
Vice-Amiral
Vice-Amiral
 
Messages: 636
Inscrit le: 10 Avr 2003 00:00
Localisation: 66

Messagepar Gesp » 17 Sep 2004 11:22

La rc4 est vraiment conseillée pour les problèmes de reconnexion.

Je n'ai plus perdu la ligne depuis longtemps.

Il n'empèche que cela devrait au moins fonctionner aussi sur a1 donc probablement que le problème vient d'une inversion des 2 cartes réseau ou d'un problème de cable.

Est-ce que le modem est synchronisé? sinon c'est un problème de liaison avec la ligne téléphonique, du genre, se brancher après un filtre et pas sur la sortie non filtrée.
Avatar de l’utilisateur
Gesp
Amiral
Amiral
 
Messages: 4481
Inscrit le: 29 Déc 2002 01:00

Suite du probléme !

Messagepar Psycotrope » 17 Sep 2004 13:54

En fait ma connexion internet fonctionne bien puisque je vous repond !!!

Je viens d'installer la RC4 toujours avec le meme modem en PPPoE, j'ai accé a l'interface web de paramaetrage ,
mais le probleme persiste, les logs :

13:46:07 red: Connectioncheck Restarting 8/10
13:46:07 pppd[6329] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
13:46:07 pppd[6329] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
13:46:07 pppd[6330] pppd 2.4.2 started by root, uid 0
13:46:08 pppd[6330] PADS: Service-Name: ''
13:46:08 pppd[6330] PPP session is 4552
13:46:08 pppd[6330] using channel 10
13:46:08 pppd[6330] Using interface ppp0
13:46:08 pppd[6330] Connect: ppp0 <--> eth1
13:46:08 pppd[6330] Couldn't increase MTU to 1500
13:46:08 pppd[6330] Couldn't increase MRU to 1500
13:46:08 pppd[6330] sent [LCP ConfReq id=0x1 <magic 0xdbf9c7e7>]
13:46:08 pppd[6330] rcvd [LCP ConfReq id=0x8f <mru 1492> <auth chap MD5> <magic 0x3cf4c190>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
13:46:08 pppd[6330] No auth is possible
13:46:08 pppd[6330] sent [LCP ConfRej id=0x8f <auth chap MD5>]
13:46:08 pppd[6330] rcvd [LCP ConfAck id=0x1 <magic 0xdbf9c7e7>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
13:46:08 pppd[6330] rcvd [LCP ConfReq id=0x90 <mru 1492> <magic 0x3cf4c190>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
13:46:08 pppd[6330] sent [LCP ConfAck id=0x90 <mru 1492> <magic 0x3cf4c190>]
13:46:08 pppd[6330] Couldn't increase MRU to 1500
13:46:08 pppd[6330] sent [LCP EchoReq id=0x0 magic=0xdbf9c7e7]
13:46:08 pppd[6330] peer from calling number 00:90:1A:40:1D:04 authorized
13:46:08 pppd[6330] sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
13:46:08 pppd[6330] rcvd [LCP TermReq id=0x91] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...
13:46:08 pppd[6330] LCP terminated by peer
13:46:08 pppd[6330] Couldn't increase MTU to 1500
13:46:08 pppd[6330] Couldn't increase MRU to 1500
13:46:08 pppd[6330] sent [LCP TermAck id=0x91]
13:46:11 pppd[6330] Connection terminated.
13:46:11 pppd[6330] Exit.
13:46:12 red: Connectioncheck RED fail to connect
13:46:31 red: Connectioncheck Restarting 8/10
13:46:31 pppd[6369] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
13:46:31 pppd[6369] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
13:46:31 pppd[6370] pppd 2.4.2 started by root, uid 0
13:46:31 pppd[6370] PADS: Service-Name: ''
13:46:31 pppd[6370] PPP session is 4556
13:46:31 pppd[6370] using channel 11
13:46:31 pppd[6370] Using interface ppp0
13:46:31 pppd[6370] Connect: ppp0 <--> eth1
13:46:31 pppd[6370] Couldn't increase MTU to 1500
13:46:31 pppd[6370] Couldn't increase MRU to 1500
13:46:31 pppd[6370] sent [LCP ConfReq id=0x1 <magic 0x2710dcf4>]
13:46:31 pppd[6370] rcvd [LCP ConfReq id=0x87 <mru 1492> <auth chap MD5> <magic 0x32ba315b>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
13:46:31 pppd[6370] No auth is possible
13:46:31 pppd[6370] sent [LCP ConfRej id=0x87 <auth chap MD5>]
13:46:31 pppd[6370] rcvd [LCP ConfAck id=0x1 <magic 0x2710dcf4>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
13:46:31 pppd[6370] rcvd [LCP ConfReq id=0x88 <mru 1492> <magic 0x32ba315b>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
13:46:31 pppd[6370] sent [LCP ConfAck id=0x88 <mru 1492> <magic 0x32ba315b>]
13:46:31 pppd[6370] Couldn't increase MRU to 1500
13:46:31 pppd[6370] sent [LCP EchoReq id=0x0 magic=0x2710dcf4]
13:46:31 pppd[6370] peer from calling number 00:90:1A:40:1D:04 authorized
13:46:31 pppd[6370] sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
13:46:31 pppd[6370] rcvd [LCP TermReq id=0x89] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...
13:46:31 pppd[6370] LCP terminated by peer
13:46:31 pppd[6370] Couldn't increase MTU to 1500
13:46:31 pppd[6370] Couldn't increase MRU to 1500
13:46:31 pppd[6370] sent [LCP TermAck id=0x89]
13:46:34 pppd[6370] Connection terminated.
13:46:34 pppd[6370] Exit.
13:46:36 red: Connectioncheck RED fail to connect


Si quelqu'un a la meme instal, comment t'a fais !!! ????
Psycotrope
Quartier Maître
Quartier Maître
 
Messages: 21
Inscrit le: 17 Sep 2004 08:26

Messagepar Gesp » 17 Sep 2004 16:46

Un des intérêts de la V1.4, c'est que c'est plus facile pour débuger les problèmes de configuration.

pppd de ton coté dit
No auth is possible


Ce doit être parce que pppd a conclut que ni pap ni chap n'étaient en état de fonctionner.
Or ton correspondant a demandé 'chap'.

Il faudrait savoir comment tu as fait pour obtenir cela.
Normalement, il devrait y avoir un message d'erreur en PPPoE si le login/mot de passe ne sont pas remplis (il se pourrait que ce soit le cas , bien que normalement du code vérifie qu'ils soient remplis). Mais si tu mets un espace pour passer outre au contrôle, je ne sais pas comment pppd va interpréter cela.

Ou alors, est-ce que tu n'as pas des caractères spéciaux dans le login / mot de passe, genre " ou ' ou * ou / ?
Le @ est supporté sans problème.

Qu'as-tu sélectionné en bas de la page pppsetup.cgi pour l'authentification?

A priori, tu devrais choisir 'PAP ou CHAP', ou PAP, ou CHAP, mettre un login et un mot de passe
Avatar de l’utilisateur
Gesp
Amiral
Amiral
 
Messages: 4481
Inscrit le: 29 Déc 2002 01:00

Le probleme subsiste (voir poste 1)

Messagepar Psycotrope » 20 Sep 2004 09:58

voici ma config dans setup je choisi PPoE en GREEN + RED.

sur IG de config sous IE , j'ai mis ça

Interface : PPoE

Config avancée PPoE : coché PPoE
Nom du service : Lan3cADSL
Concentrateur WAnadoo

Login : fti\xxxxx
Mot de Passe : xxxxxxx
Methode : PAP/CHAP
DNS : Auto

Nulle part je peut présiser VPI VCI ????????

voici le log Kernel :

IPCop diagnostics
Section: red Date: 20 Septembre

08:51:21 kernel: eth0 link up, 100Mbps, full-duplex, lpa 0x45E1
08:54:14 kernel: usb.c registered new driver usbdevfs
08:54:14 kernel: usb.c registered new driver hub
08:54:14 kernel: usb-uhci.c: $Revision 1.275 $ time 18:21:58 Sep 14 2004
08:54:14 kernel: usb-uhci.c High bandwidth mode enabled
08:54:14 kernel: usb-uhci.c USB UHCI at I/O 0xc400, IRQ 11
08:54:14 kernel: usb-uhci.c Detected 2 ports
08:54:14 kernel: usb.c new USB bus registered, assigned bus number 1
08:54:14 kernel: usb-uhci.c USB UHCI at I/O 0xc800, IRQ 11
08:54:14 kernel: usb-uhci.c Detected 2 ports
08:54:14 kernel: usb.c new USB bus registered, assigned bus number 2
08:54:14 kernel: usb-uhci.c v1.275:USB Universal Host Controller Interface driver
08:54:14 kernel: usb.c registered new driver usb-storage
08:54:14 kernel: usb.c registered new driver hiddev
08:54:14 kernel: usb.c registered new driver hid
08:54:14 kernel: usb.c registered new driver acm
08:54:15 kernel: eth0 RealTek RTL8139 at 0xc808e000, 00:08:54:1b:21:22, IRQ 10
08:54:15 kernel: eth1 RealTek RTL8139 at 0xc8090000, 00:10:dc:90:6c:87, IRQ 11
08:54:16 kernel: eth0 link up, 100Mbps, full-duplex, lpa 0x45E1
08:54:17 kernel: eth1 link up, 10Mbps, half-duplex, lpa 0x0000
08:54:17 pppd[260] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
08:54:17 pppd[260] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
08:54:17 pppd[262] pppd 2.4.2 started by root, uid 0
08:54:52 pppd[262] Timeout waiting for PADO packets
08:54:52 pppd[262] Unable to complete PPPoE Discovery
08:54:52 pppd[262] Exit.
08:54:52 red: Connectioncheck RED fail to connect
08:55:22 red: Connectioncheck Restarting 1/10
08:55:23 pppd[357] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
08:55:23 pppd[357] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
08:55:23 pppd[358] pppd 2.4.2 started by root, uid 0
08:55:58 pppd[358] Timeout waiting for PADO packets
08:55:58 pppd[358] Unable to complete PPPoE Discovery
08:55:58 pppd[358] Exit.
08:55:58 red: Connectioncheck RED fail to connect
08:58:01 kernel: eth1 link down
08:58:05 kernel: eth0 link down
08:58:07 kernel: eth1 link up, 100Mbps, full-duplex, lpa 0x45E1
08:58:08 kernel: eth0 link up, 10Mbps, half-duplex, lpa 0x0000
08:58:23 kernel: eth0 link up, 10Mbps, half-duplex, lpa 0x0000
08:58:23 pppd[548] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
08:58:23 pppd[548] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
08:58:23 pppd[549] pppd 2.4.2 started by root, uid 0
08:59:39 kernel: usb.c registered new driver usbdevfs
08:59:39 kernel: usb.c registered new driver hub
08:59:39 kernel: usb-uhci.c: $Revision 1.275 $ time 18:21:58 Sep 14 2004
08:59:39 kernel: usb-uhci.c High bandwidth mode enabled
08:59:39 kernel: usb-uhci.c USB UHCI at I/O 0xc400, IRQ 11
08:59:39 kernel: usb-uhci.c Detected 2 ports
08:59:39 kernel: usb.c new USB bus registered, assigned bus number 1
08:59:39 kernel: usb-uhci.c USB UHCI at I/O 0xc800, IRQ 11
08:59:39 kernel: usb-uhci.c Detected 2 ports
08:59:39 kernel: usb.c new USB bus registered, assigned bus number 2
08:59:39 kernel: usb-uhci.c v1.275:USB Universal Host Controller Interface driver
08:59:39 kernel: usb.c registered new driver usb-storage
08:59:39 kernel: usb.c registered new driver hiddev
08:59:39 kernel: usb.c registered new driver hid
08:59:39 kernel: usb.c registered new driver acm
08:59:40 kernel: eth0 RealTek RTL8139 at 0xc808e000, 00:08:54:1b:21:22, IRQ 10
08:59:40 kernel: eth1 RealTek RTL8139 at 0xc8090000, 00:10:dc:90:6c:87, IRQ 11
08:59:41 kernel: eth0 link up, 10Mbps, half-duplex, lpa 0x0000
08:59:42 kernel: eth1 link up, 100Mbps, full-duplex, lpa 0x45E1
08:59:42 pppd[261] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
08:59:42 pppd[261] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
08:59:42 pppd[263] pppd 2.4.2 started by root, uid 0
09:00:17 pppd[263] Timeout waiting for PADO packets
09:00:17 pppd[263] Unable to complete PPPoE Discovery
09:00:17 pppd[263] Exit.
09:00:17 red: Connectioncheck RED fail to connect
09:00:47 red: Connectioncheck Restarting 1/10
09:00:48 pppd[358] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:00:48 pppd[358] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:00:48 pppd[359] pppd 2.4.2 started by root, uid 0
09:01:23 pppd[359] Timeout waiting for PADO packets
09:01:23 pppd[359] Unable to complete PPPoE Discovery
09:01:23 pppd[359] Exit.
09:01:23 red: Connectioncheck RED fail to connect
09:01:53 red: Connectioncheck Restarting 2/10
09:01:53 pppd[414] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:01:53 pppd[414] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:01:53 pppd[415] pppd 2.4.2 started by root, uid 0
09:02:28 pppd[415] Timeout waiting for PADO packets
09:02:28 pppd[415] Unable to complete PPPoE Discovery
09:02:28 pppd[415] Exit.
09:02:28 red: Connectioncheck RED fail to connect
09:02:58 red: Connectioncheck Restarting 3/10
09:02:59 pppd[468] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:02:59 pppd[468] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:02:59 pppd[469] pppd 2.4.2 started by root, uid 0
09:03:34 pppd[469] Timeout waiting for PADO packets
09:03:34 pppd[469] Unable to complete PPPoE Discovery
09:03:34 pppd[469] Exit.
09:03:34 red: Connectioncheck RED fail to connect
09:04:04 red: Connectioncheck Restarting 4/10
09:04:04 pppd[523] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:04:04 pppd[523] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:04:04 pppd[524] pppd 2.4.2 started by root, uid 0
09:04:39 pppd[524] Timeout waiting for PADO packets
09:04:39 pppd[524] Unable to complete PPPoE Discovery
09:04:39 pppd[524] Exit.
09:04:39 red: Connectioncheck RED fail to connect
09:05:09 red: Connectioncheck Restarting 5/10
09:05:10 pppd[594] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:05:10 pppd[594] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:05:10 pppd[595] pppd 2.4.2 started by root, uid 0
09:05:45 pppd[595] Timeout waiting for PADO packets
09:05:45 pppd[595] Unable to complete PPPoE Discovery
09:05:45 pppd[595] Exit.
09:05:45 red: Connectioncheck RED fail to connect
09:06:15 red: Connectioncheck Restarting 6/10
09:06:15 pppd[646] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:06:15 pppd[646] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:06:15 pppd[647] pppd 2.4.2 started by root, uid 0
09:06:50 pppd[647] Timeout waiting for PADO packets
09:06:50 pppd[647] Unable to complete PPPoE Discovery
09:06:50 pppd[647] Exit.
09:06:50 red: Connectioncheck RED fail to connect
09:07:21 red: Connectioncheck Restarting 7/10
09:07:21 pppd[700] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:07:21 pppd[700] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:07:21 pppd[701] pppd 2.4.2 started by root, uid 0
09:07:56 pppd[701] Timeout waiting for PADO packets
09:07:56 pppd[701] Unable to complete PPPoE Discovery
09:07:56 pppd[701] Exit.
09:07:56 red: Connectioncheck RED fail to connect
09:08:22 kernel: eth1 link down
09:08:24 kernel: eth0 link down
09:08:25 kernel: eth1 link up, 10Mbps, half-duplex, lpa 0x0000
09:08:26 red: Connectioncheck Restarting 8/10
09:08:26 pppd[755] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:08:26 pppd[755] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:08:26 pppd[756] pppd 2.4.2 started by root, uid 0
09:08:28 kernel: eth0 link up, 100Mbps, full-duplex, lpa 0x45E1
09:09:01 pppd[756] Timeout waiting for PADO packets
09:09:01 pppd[756] Unable to complete PPPoE Discovery
09:09:01 pppd[756] Exit.
09:09:01 red: Connectioncheck RED fail to connect
09:09:32 red: Connectioncheck Restarting 9/10
09:09:32 pppd[808] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:09:32 pppd[808] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:09:32 pppd[809] pppd 2.4.2 started by root, uid 0
09:10:07 pppd[809] Timeout waiting for PADO packets
09:10:07 pppd[809] Unable to complete PPPoE Discovery
09:10:07 pppd[809] Exit.
09:10:07 red: Connectioncheck RED fail to connect
09:10:37 red: Connectioncheck Restarting 10/10
09:10:37 red: Connectioncheck Clearing RED interface
09:10:38 pppd[946] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:10:38 pppd[946] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:10:38 pppd[947] pppd 2.4.2 started by root, uid 0
09:11:13 pppd[947] Timeout waiting for PADO packets
09:11:13 pppd[947] Unable to complete PPPoE Discovery
09:11:13 pppd[947] Exit.
09:11:13 red: Connectioncheck RED fail to connect
09:11:43 red: Connectioncheck Restarting 1/10
09:11:43 pppd[1048] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:11:43 pppd[1048] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:11:43 pppd[1049] pppd 2.4.2 started by root, uid 0
09:12:18 pppd[1049] Timeout waiting for PADO packets
09:12:18 pppd[1049] Unable to complete PPPoE Discovery
09:12:18 pppd[1049] Exit.
09:12:18 red: Connectioncheck RED fail to connect
09:12:49 red: Connectioncheck Restarting 2/10
09:12:49 pppd[1097] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:12:49 pppd[1097] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:12:49 pppd[1098] pppd 2.4.2 started by root, uid 0
09:13:24 pppd[1098] Timeout waiting for PADO packets
09:13:24 pppd[1098] Unable to complete PPPoE Discovery
09:13:24 pppd[1098] Exit.
09:13:24 red: Connectioncheck RED fail to connect
09:13:54 red: Connectioncheck Restarting 3/10
09:13:54 pppd[1169] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:13:54 pppd[1169] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:13:54 pppd[1170] pppd 2.4.2 started by root, uid 0
09:14:29 pppd[1170] Timeout waiting for PADO packets
09:14:29 pppd[1170] Unable to complete PPPoE Discovery
09:14:29 pppd[1170] Exit.
09:14:29 red: Connectioncheck RED fail to connect
09:15:00 red: Connectioncheck Restarting 4/10
09:15:00 pppd[1250] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
09:15:00 pppd[1250] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
09:15:00 pppd[1251] pppd 2.4.2 started by root, uid 0
09:15:00 pppd[1251] PADS: Service-Name: ''
09:15:00 pppd[1251] PPP session is 3914
09:15:00 pppd[1251] using channel 1
09:15:00 pppd[1251] Using interface ppp0
09:15:00 pppd[1251] Connect: ppp0 <--> eth1
09:15:00 pppd[1251] Couldn't increase MTU to 1500
09:15:00 pppd[1251] Couldn't increase MRU to 1500
09:15:00 pppd[1251] sent [LCP ConfReq id=0x1 <magic 0x71e97c59>]
09:15:00 pppd[1251] rcvd [LCP ConfReq id=0xa7 <mru 1492> <auth chap MD5> <magic 0x25510d1>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
09:15:00 pppd[1251] No auth is possible
09:15:00 pppd[1251] sent [LCP ConfRej id=0xa7 <auth chap MD5>]
09:15:00 pppd[1251] rcvd [LCP ConfAck id=0x1 <magic 0x71e97c59>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
09:15:00 pppd[1251] rcvd [LCP ConfReq id=0xa8 <mru 1492> <magic 0x25510d1>] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 88 88 88 88
09:15:00 pppd[1251] sent [LCP ConfAck id=0xa8 <mru 1492> <magic 0x25510d1>]
09:15:00 pppd[1251] Couldn't increase MRU to 1500
09:15:00 pppd[1251] sent [LCP EchoReq id=0x0 magic=0x71e97c59]
09:15:00 pppd[1251] peer from calling number 00:90:1A:40:1D:04 authorized
09:15:00 pppd[1251] sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
09:15:00 pppd[1251] rcvd [LCP TermReq id=0xa9] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...
09:15:00 pppd[1251] LCP terminated by peer
09:15:00 pppd[1251] Couldn't increase MTU to 1500
09:15:00 pppd[1251] Couldn't increase MRU to 1500
09:15:00 pppd[1251] sent [LCP TermAck id=0xa9]
09:15:03 pppd[1251] Connection terminated.
09:15:03 pppd[1251] Exit.
09:15:05 red: Connectioncheck RED fail to connect
09:15:35 red: Connectioncheck Restarting 5/10
09:15:35 pppd[1331] pppd 2.4.2 started by root, uid 0
09:15:36 pppd[1331] using channel 1
09:15:36 pppd[1331] Using interface ppp0
09:15:36 pppd[1331] Connect: ppp0 <--> /dev/pts/0
09:15:37 pppd[1331] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x8735691c>]
09:16:03 pppd[1331] Terminating on signal 15.
09:16:03 pppd[1331] sent [LCP TermReq id=0x2 "User request"]
09:16:05 pppd[1331] Terminating on signal 15.
09:16:06 pppd[1331] sent [LCP TermReq id=0x3 "User request"]
09:16:08 pppd[1331] Terminating on signal 15.
09:16:09 pppd[1331] Connection terminated.
09:16:09 pppd[1331] Waiting for 1 child processes...
09:16:09 pppd[1331] script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo, pid 1332
09:16:10 pppd[1331] Terminating on signal 15.
09:16:10 pppd[1331] Waiting for 1 child processes...
09:16:10 pppd[1331] script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo, pid 1332
09:16:11 pppoe[1332] Timeout waiting for PADO packets
09:16:11 pppd[1331] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 1332), status = 0x1
09:16:11 pppd[1331] Exit.
09:17:10 pppd[1540] pppd 2.4.2 started by root, uid 0
09:17:10 pppd[1540] using channel 2
09:17:10 pppd[1540] Using interface ppp0
09:17:10 pppd[1540] Connect: ppp0 <--> /dev/pts/0
09:17:11 pppd[1540] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0xef69bc4>]
09:17:45 pppoe[1541] Timeout waiting for PADO packets
09:17:45 pppd[1540] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 1541), status = 0x1
09:17:45 pppd[1540] Modem hangup
09:17:45 pppd[1540] Connection terminated.
09:17:45 pppd[1540] Exit.
09:17:50 red: Connectioncheck RED fail to connect
09:18:20 red: Connectioncheck Restarting 1/10
09:18:21 pppd[1640] pppd 2.4.2 started by root, uid 0
09:18:21 pppd[1640] using channel 3
09:18:21 pppd[1640] Using interface ppp0
09:18:21 pppd[1640] Connect: ppp0 <--> /dev/pts/0
09:18:22 pppd[1640] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0xb64b968>]
09:18:56 pppoe[1641] Timeout waiting for PADO packets
09:18:56 pppd[1640] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 1641), status = 0x1
09:18:56 pppd[1640] Modem hangup
09:18:56 pppd[1640] Connection terminated.
09:18:56 pppd[1640] Exit.
09:18:56 red: Connectioncheck RED fail to connect
09:19:26 red: Connectioncheck Restarting 2/10
09:19:26 pppd[1739] pppd 2.4.2 started by root, uid 0
09:19:26 pppd[1739] using channel 4
09:19:26 pppd[1739] Using interface ppp0
09:19:26 pppd[1739] Connect: ppp0 <--> /dev/pts/0
09:19:27 pppd[1739] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x12f173f4>]
09:20:00 pppd[1739] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x12f173f4>]
09:20:01 pppoe[1740] Timeout waiting for PADO packets
09:20:01 pppd[1739] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 1740), status = 0x1
09:20:01 pppd[1739] Modem hangup
09:20:01 pppd[1739] Connection terminated.
09:20:01 pppd[1739] Exit.
09:20:01 red: Connectioncheck RED fail to connect
09:20:31 red: Connectioncheck Restarting 3/10
09:20:32 pppd[1829] pppd 2.4.2 started by root, uid 0
09:20:32 pppd[1829] using channel 5
09:20:32 pppd[1829] Using interface ppp0
09:20:32 pppd[1829] Connect: ppp0 <--> /dev/pts/0
09:20:33 pppd[1829] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0xdeec0b3c>]
09:21:07 pppoe[1830] Timeout waiting for PADO packets
09:21:07 pppd[1829] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 1830), status = 0x1
09:21:07 pppd[1829] Modem hangup
09:21:07 pppd[1829] Connection terminated.
09:21:07 pppd[1829] Exit.
09:21:07 red: Connectioncheck RED fail to connect
09:21:37 red: Connectioncheck Restarting 4/10
09:21:37 pppd[1895] pppd 2.4.2 started by root, uid 0
09:21:37 pppd[1895] using channel 6
09:21:37 pppd[1895] Using interface ppp0
09:21:37 pppd[1895] Connect: ppp0 <--> /dev/pts/0
09:21:38 pppd[1895] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0xb6da5178>]
09:22:12 pppoe[1896] Timeout waiting for PADO packets
09:22:12 pppd[1895] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 1896), status = 0x1
09:22:12 pppd[1895] Modem hangup
09:22:12 pppd[1895] Connection terminated.
09:22:12 pppd[1895] Exit.
09:22:12 red: Connectioncheck RED fail to connect
09:22:42 red: Connectioncheck Restarting 5/10
09:22:43 pppd[1949] pppd 2.4.2 started by root, uid 0
09:22:43 pppd[1949] using channel 7
09:22:43 pppd[1949] Using interface ppp0
09:22:43 pppd[1949] Connect: ppp0 <--> /dev/pts/0
09:22:44 pppd[1949] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0xcd697292>]
09:23:18 pppoe[1951] Timeout waiting for PADO packets
09:23:18 pppd[1949] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 1951), status = 0x1
09:23:18 pppd[1949] Modem hangup
09:23:18 pppd[1949] Connection terminated.
09:23:18 pppd[1949] Exit.
09:23:18 red: Connectioncheck RED fail to connect
09:23:48 red: Connectioncheck Restarting 6/10
09:23:48 pppd[2005] pppd 2.4.2 started by root, uid 0
09:23:48 pppd[2005] using channel 8
09:23:48 pppd[2005] Using interface ppp0
09:23:48 pppd[2005] Connect: ppp0 <--> /dev/pts/0
09:23:49 pppd[2005] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x2b64e09>]
09:24:23 pppoe[2007] Timeout waiting for PADO packets
09:24:23 pppd[2005] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 2007), status = 0x1
09:24:23 pppd[2005] Modem hangup
09:24:23 pppd[2005] Connection terminated.
09:24:23 pppd[2005] Exit.
09:24:23 red: Connectioncheck RED fail to connect
09:24:53 red: Connectioncheck Restarting 7/10
09:24:54 pppd[2070] pppd 2.4.2 started by root, uid 0
09:24:54 pppd[2070] using channel 9
09:24:54 pppd[2070] Using interface ppp0
09:24:54 pppd[2070] Connect: ppp0 <--> /dev/pts/0
09:24:55 pppd[2070] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x18e349cc>]
09:24:58 pppd[2070] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x18e349cc>]
09:25:01 pppd[2070] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x18e349cc>]
09:25:29 pppoe[2072] Timeout waiting for PADO packets
09:25:29 pppd[2070] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 2072), status = 0x1
09:25:29 pppd[2070] Modem hangup
09:25:29 pppd[2070] Connection terminated.
09:25:29 pppd[2070] Exit.
09:25:29 red: Connectioncheck RED fail to connect
09:25:59 red: Connectioncheck Restarting 8/10
09:25:59 pppd[2152] pppd 2.4.2 started by root, uid 0
09:25:59 pppd[2152] using channel 10
09:25:59 pppd[2152] Using interface ppp0
09:25:59 pppd[2152] Connect: ppp0 <--> /dev/pts/0
09:26:00 pppd[2152] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x9d7171c7>]
09:26:34 pppoe[2154] Timeout waiting for PADO packets
09:26:34 pppd[2152] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 -S Lan3cADSL -C WAnadoo finished (pid 2154), status = 0x1
09:26:34 pppd[2152] Modem hangup
09:26:34 pppd[2152] Connection terminated.
09:26:34 pppd[2152] Exit.
09:26:34 red: Connectioncheck RED fail to connect


comment fo faire ???[/img]
Psycotrope
Quartier Maître
Quartier Maître
 
Messages: 21
Inscrit le: 17 Sep 2004 08:26

suite du probleme

Messagepar Psycotrope » 20 Sep 2004 12:19

En fait j'ai 2 Realtech 3169 une sur carte mere, et l'autre sur PCI, et j'ai l'impression qu IPcop se trompe de catre!!!

Si j'installe IPCop sans la carte pci il installe l'interface vert (GREEN + Modem)
Ensuite j'eteint IPCop, je met ma carte PCI je redémarre.
La l'interface verte est passé sur ma carte PCI ?????
sans meme l'installer !!


quoi qu'y se passe ???
Psycotrope
Quartier Maître
Quartier Maître
 
Messages: 21
Inscrit le: 17 Sep 2004 08:26

Derniere espoir : modem ADSL ECI b-Focus sur ethernet

Messagepar Psycotrope » 20 Sep 2004 13:56

j'ai 2 carte PCI realtech 8139, une GREEN une RED
Toujours mon modem ADSL ECI b-Focus sur ethernet
DHCP sur GREEN
PPPoE sur RED
config IE PPPoe sans plugin (ou je dois rajouter les param VPI VCI ????)

les log RED + DEBUG :

13:34:03 kernel: usb.c registered new driver usbdevfs
13:34:03 kernel: usb.c registered new driver hub
13:34:03 kernel: usb-uhci.c: $Revision 1.275 $ time 18:21:58 Sep 14 2004
13:34:03 kernel: usb-uhci.c High bandwidth mode enabled
13:34:03 kernel: usb-uhci.c USB UHCI at I/O 0xd400, IRQ 5
13:34:03 kernel: usb-uhci.c Detected 2 ports
13:34:03 kernel: usb.c new USB bus registered, assigned bus number 1
13:34:03 kernel: usb-uhci.c USB UHCI at I/O 0xd800, IRQ 5
13:34:03 kernel: usb-uhci.c Detected 2 ports
13:34:03 kernel: usb.c new USB bus registered, assigned bus number 2
13:34:03 kernel: usb-uhci.c v1.275:USB Universal Host Controller Interface driver
13:34:03 kernel: usb.c registered new driver usb-storage
13:34:03 kernel: usb.c registered new driver hiddev
13:34:03 kernel: usb.c registered new driver hid
13:34:03 kernel: usb.c registered new driver acm
13:34:04 kernel: eth0 RealTek RTL8139 at 0xc808e000, 00:08:54:1b:21:22, IRQ 10
13:34:04 kernel: eth1 RealTek RTL8139 at 0xc8090000, 00:08:a1:40:5f:b3, IRQ 11
13:34:05 kernel: eth0 link up, 10Mbps, half-duplex, lpa 0x0000
13:35:04 kernel: eth0 link up, 10Mbps, half-duplex, lpa 0x0000
13:38:34 kernel: usb.c registered new driver usbdevfs
13:38:34 kernel: usb.c registered new driver hub
13:38:34 kernel: usb-uhci.c: $Revision 1.275 $ time 18:21:58 Sep 14 2004
13:38:34 kernel: usb-uhci.c High bandwidth mode enabled
13:38:34 kernel: usb-uhci.c USB UHCI at I/O 0xd400, IRQ 5
13:38:34 kernel: usb-uhci.c Detected 2 ports
13:38:34 kernel: usb.c new USB bus registered, assigned bus number 1
13:38:34 kernel: usb-uhci.c USB UHCI at I/O 0xd800, IRQ 5
13:38:34 kernel: usb-uhci.c Detected 2 ports
13:38:34 kernel: usb.c new USB bus registered, assigned bus number 2
13:38:34 kernel: usb-uhci.c v1.275:USB Universal Host Controller Interface driver
13:38:34 kernel: usb.c registered new driver usb-storage
13:38:34 kernel: usb.c registered new driver hiddev
13:38:34 kernel: usb.c registered new driver hid
13:38:34 kernel: usb.c registered new driver acm
13:38:35 kernel: eth0 RealTek RTL8139 at 0xc808e000, 00:08:54:1b:21:22, IRQ 10
13:38:35 kernel: eth1 RealTek RTL8139 at 0xc8090000, 00:08:a1:40:5f:b3, IRQ 11
13:38:36 kernel: eth0 link up, 10Mbps, half-duplex, lpa 0x0000
13:40:16 kernel: eth0 link down
13:40:18 kernel: eth0 link up, 100Mbps, full-duplex, lpa 0x45E1
13:41:30 kernel: eth1 link up, 10Mbps, half-duplex, lpa 0x0000
13:41:31 pppd[395] Plugin /usr/lib/pppd/2.4.2/rp-pppoe.so loaded.
13:41:31 pppd[395] RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
13:41:31 pppd[396] pppd 2.4.2 started by root, uid 0
13:41:31 pppd[396] PPP session is 7528
13:41:31 pppd[396] Using interface ppp0
13:41:31 pppd[396] Connect: ppp0 <--> eth1
13:41:31 pppd[396] Couldn't increase MTU to 1500
13:41:31 pppd[396] Couldn't increase MRU to 1500
13:41:31 pppd[396] Couldn't increase MRU to 1500
13:41:31 pppd[396] peer from calling number 00:90:1A:40:1D:04 authorized
13:41:31 pppd[396] LCP terminated by peer
13:41:31 pppd[396] Couldn't increase MTU to 1500
13:41:31 pppd[396] Couldn't increase MRU to 1500
13:41:34 pppd[396] Connection terminated.
13:41:34 pppd[396] Exit.
13:43:10 pppd[798] pppd 2.4.2 started by root, uid 0
13:43:10 pppd[798] using channel 1
13:43:10 pppd[798] Using interface ppp0
13:43:10 pppd[798] Connect: ppp0 <--> /dev/pts/0
13:43:10 pppoe[799] PADS: Service-Name: ''
13:43:10 pppoe[799] PPP session is 7552
13:43:10 pppd[798] rcvd [LCP ConfReq id=0x45 <mru 1492> <auth chap MD5> <magic 0x49666bfc>]
13:43:10 pppd[798] sent [LCP ConfReq id=0x1 <mru 1492> <magic 0xbfff4cf4>]
13:43:10 pppd[798] No auth is possible
13:43:10 pppd[798] sent [LCP ConfRej id=0x45 <auth chap MD5>]
13:43:11 pppd[798] rcvd [LCP ConfAck id=0x1 <mru 1492> <magic 0xbfff4cf4>]
13:43:11 pppd[798] rcvd [LCP ConfReq id=0x46 <mru 1492> <magic 0x49666bfc>]
13:43:11 pppd[798] sent [LCP ConfAck id=0x46 <mru 1492> <magic 0x49666bfc>]
13:43:11 pppd[798] sent [LCP EchoReq id=0x0 magic=0xbfff4cf4]
13:43:11 pppd[798] sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
13:43:11 pppd[798] rcvd [LCP TermReq id=0x47]
13:43:11 pppd[798] LCP terminated by peer
13:43:11 pppd[798] sent [LCP TermAck id=0x47]
13:43:11 pppoe[799] Session 7552 terminated -- received PADT from peer
13:43:11 pppoe[799] Sent PADT
13:43:11 pppd[798] Script /usr/sbin/pppoe -p /var/run/pppoe.pid -I eth1 -T 80 -U -m 1412 finished (pid 799), status = 0x0
13:43:11 pppd[798] Modem hangup
13:43:11 pppd[798] Connection terminated.
13:43:11 pppd[798] Exit.


GESP aide moi stp sinon, quel modem marche tres bien avec IPCop.
Psycotrope
Quartier Maître
Quartier Maître
 
Messages: 21
Inscrit le: 17 Sep 2004 08:26

Messagepar Gesp » 20 Sep 2004 14:20

Config avancée PPoE : coché PPoE
Nom du service : Lan3cADSL <= ne met rien dedans
Concentrateur WAnadoo <= ne met rien dedans

Login : fti\xxxxx <= peut-être pas bon, ce devrait être fti\xxxxx@fti
Mot de Passe : xxxxxxx
Methode : PAP/CHAP
DNS : Auto

Nulle part je peut présiser VPI VCI ????????

Quand un modem ethernet est en bridge, soit il s'autoconfigure de lui-même pour les VPI/VCI qui vont bien, soit cela se configure sur l'interface web du modem. Donc c'est normal qu'il n'y ait rien dans l'interface web d'IPCop
Avatar de l’utilisateur
Gesp
Amiral
Amiral
 
Messages: 4481
Inscrit le: 29 Déc 2002 01:00

Messagepar Gesp » 20 Sep 2004 14:31

Si j'installe IPCop sans la carte pci il installe l'interface vert (GREEN + Modem)
Ensuite j'eteint IPCop, je met ma carte PCI je redémarre.
La l'interface verte est passé sur ma carte PCI ?????
sans meme l'installer !!


quoi qu'y se passe ???


Des manip comme celle-là ne sont pas supportées par l'interface de configuration.
Il n'y a pas de vérification par rapport à l'adresse MAC de chaque carte.

De même si tu as 2 cartes identiques dont tu changes l'ordre sur les connecteurs PCI, les cartes seront inversées.

Pour ne pas te tromper sur les sorties, tu peux peut-être utiliser mii-tool sur l'une puis l'autre interface.
eth0 étant nécessaire la green.
Avatar de l’utilisateur
Gesp
Amiral
Amiral
 
Messages: 4481
Inscrit le: 29 Déc 2002 01:00

Messagepar thejud » 20 Sep 2004 14:33

Bonjour,

ça vaut ce que ça vaut comme explication, mais je tenais à signaler pour ma propre expérience, que j'avais un peu la même config de départ (Modem B-Focus ethernet et deux cartes Realtek) et j'ai eu pas mal de soucis.

Ma solution sans être la plus parfaite, c'est le remplacement des deux realtek par deux cartes 3Com et là 0 problèmes, installation, config et connexion en même pas une demi-heure.

J'avais eu ce souci avec mon serveur sme il y a deux ans et à l'époque on m'avait suggéré de faire des essais avec des carte réseau basées sur des chips autres que des 8139 realtek, et cela avait porté ses fruits.

Voilà ce que je peux vous dire pour ma part. Si cela peut aider quelque'un, je ne dis pas que c'est LA solution et que cela va marcher, mais parfois, il y a souci. Peut être alors qu'en commençant par tester avec au moins une autre carte différente.


Bonne journée et en espérant que cela puisse aider

J
Avatar de l’utilisateur
thejud
Premier-Maître
Premier-Maître
 
Messages: 57
Inscrit le: 10 Nov 2003 01:00
Localisation: 17

Messagepar Psycotrope » 20 Sep 2004 14:55

Toujours rien de mieux !! Merci jud, GESP et les autres , je vais voir si je peut trouver une carte reseau autre.

Pour info mon modem c sa http://www.hifocus.net/bfocus.php3
Psycotrope
Quartier Maître
Quartier Maître
 
Messages: 21
Inscrit le: 17 Sep 2004 08:26

Messagepar Gesp » 20 Sep 2004 16:57

Je voudrais bien savoir pourquoi tu as 'No auth is possible'

Tu peux regarder dans /var/ppp/seetings :
- si tu as un login enregistré
- si tu as un mot de passe enregistré

ensuite que tu vérifies que c'est correctement écrit dans /var/ipcop/ppp/pap-or-chap (le nom et l'emplacement sont de mémoire mais cela ne doit pas être loin)

Aussi, est-ce que tu ne fais pas une erreur dans le login fti/ et non fti\?
Avatar de l’utilisateur
Gesp
Amiral
Amiral
 
Messages: 4481
Inscrit le: 29 Déc 2002 01:00

Messagepar Psycotrope » 21 Sep 2004 09:22

Probleme Résolu ! merci GESP.

Je récapitule :

- carte mere avec carte reseau intégrée : MS6368 Ver5 (MSI)

Avec la carte reseau intégrée IPCop ne fonctionne pas il detecte une mauvaise carte realtech 8139


- J'ai donc mis deux Realtech 8139


- cela ne marché pas ! normal en réinstallent j'ai mal configuré mon login de connexion.



- Param en PPPoE sur le setup d'install et PPPoE (sans le plugin dans l'interface web)




Et voila ! tout marche bien !!!
Psycotrope
Quartier Maître
Quartier Maître
 
Messages: 21
Inscrit le: 17 Sep 2004 08:26


Retour vers IPCop

Qui est en ligne ?

Utilisateur(s) parcourant actuellement ce forum : Aucun utilisateur inscrit et 0 invité(s)

cron